Dynamic two-dimensional characterization technique and influencing factors analysis of the hygroscopicity of Chinese medicine extracts / 药学学报

This study aims to construct a dynamic two-dimensional characterization technique for the hygroscopicity of traditional Chinese medicine extracts and investigate the effect of material properties of powders on hygroscopicity. The dynamic hygroscopicity-time curves of the powders were measured at 25 ℃ and 75% humidity, and the semi-equilibrium hygroscopicity time (t1/2) and equilibrium hygroscopicity (F∞) were derived as two-dimensional evaluation indicators. Finally, the correlation between the material properties and the hygroscopic behavior was analyzed by principal component analysis (PCA) and partial least squares analysis (PLS). The results showed that the dynamic two-dimensional characterization system of hygroscopicity constructed with 1/t1/2 = 0.1 h-1 and F∞ = 15% as the center can classify the hygroscopic behavior of traditional Chinese medicine extracts into four categories: fast hygroscopicity with strong hygroscopicity, slow hygroscopicity with strong hygroscopicity, fast hygroscopicity with weak hygroscopicity and slow hygroscopicity with weak hygroscopicity. The moisture absorption was negatively correlated with D50, D90, ρb and ρt; the moisture absorption rate was negatively correlated with D10, D50, D90, ρb, ρt, and positively correlated with moisture content. The hygroscopicity dynamic two-dimensional characterization indicators of Chinese medicine extracts (CMEs) constructed in this study matched with the physical properties. The method of dynamic multi-dimensional characterization technology is feasible and scientific, and the idea has strong promotional value.

Quality Evaluation of Physical Properties of Ultrafine Granular Powder of Salviae Miltiorrhizae Radix et Rhizoma / 中国实验方剂学杂志

Objective:Taking ultrafine granular powder of Salviae Miltiorrhizae Radix et Rhizoma （UGPSMR） as the research object， to establish a method for evaluating its physical properties. Method:A method was established for measuring the particle size distribution and specific surface area of UGPSMR， and the methodological investigation was carried out. A total of 15 physical indicators ［D90 （particle size value when the cumulative particle distribution reaches 90%）， particle size distribution range， particle size distribution width， bulk density， tap density， intergranular porosity， Carr index， specific surface area， pore volume， angle of repose， tablet angle， Hausner ratio， black to white degree L*， red to green degree a*， yellow to blue degree b*］ were used to characterize the quality attributes of UGPSMR and to construct the physical fingerprint. Multivariate statistical analysis methods such as similarity analysis， cluster analysis （CA）， principal component analysis （PCA） and orthogonal partial least squares discriminant analysis （OPLS-DA） were used to evaluate the quality of 11 batches of UGPSMR （S1-S11） produced in different years， and to find out the difference index between samples from different batches. Result:The method for measuring the particle size distribution and specific surface area of UGPSMR was feasible and repeatable. The similarities between the physical fingerprint of 10 batches of samples （S1-S3， S5-S11） from production and control fingerprint of UGPSMR were above 0.85， but the similarity between sample S4 and the control fingerprint was only 0.488. There were some differences in physical property indicators between different batches of UGPSMR， and the characteristic difference indicators were intergranular porosity， specific surface area， pore volume， b*， L*， Carr index， particle size distribution width， respectively. Conclusion:This method can comprehensively evaluate the physical quality attributes of UGPSMR， and can reflect the effect of differences in material basis of the medicinal materials or production process on the physical properties of finished products， and can evaluate quality consistency between batches from the physical state level， which provides new ideas for the quality control of ultrafine granular powder of herbal medicine.

Development status and research strategy of traditional Chinese medicine temporary prescription preparation technology / 中国中药杂志

Temporary prescription preparation is the preparation processed into different dosage forms by relevant pharmacist according to the temporary preparation requirement and the personalized prescription made by the doctor in accordance with the syndrome differentiation and drug performance.It is an important part in personalized pharmaceutical services.Rational design of process route,production equipment and quality control method for the temporary prescription preparation,and establishment of technology research strategy and mode in accordance with the characteristics of traditional Chinese medicine temporary prescription preparations play an important role in promoting the development of the temporary prescription preparations.To promote the normalization,standardization and intelligent development of temporary prescription preparations,we would comprehensively summarize the significance,policy,technology characteristics,technology research status quo and existing problems in this paper,and put forward the research direction of temporary prescription preparation technology based on the physical properties of raw materials,equipment research strategy,and intelligent manufacturing technology.Thus it will push the inheritance and innovation of temporary prescription preparation.

Bioadhesive pellets of astragalosides: preparation and adhesive evaluation based on the physical properties of wet mass / 药学学报

Bioadhesive preparation can be attached to specific sites to control drug release rate, increase drug concentration and increase efficacy, which is based on natural or synthetic polymer material. In this paper, based on the physical properties of wet mass, a method for screening adhesion formulation was proposed, which was different from conventional way of screening optimal formulation, and astragalosides loaded bioadhesive pellets were prepared by extrusion-spheronization method (extrusion speed 30 r·min-1, spheronization speed 808 r·min-1, spheronization time 7.5 min) based on this formulation screening method, small living animal imaging technology and mucin from porcine stomach model were used to evaluate the in vivo and invitro adhesiveness behaviour of the pellets. According to the relationship between the physical properties of wet mass and the formability and adhesiveness of bioadhesive pellets, five key physical properties hardness (Ha), adhesiveness (Ad), springiness (Sp), cohesiveness (Co), chewiness (Ch) were selected as the index of screening optimal formulation, therefore a comprehensive evaluation model was established, which based on principal component analysis, to did digital ranking for these proposed adhesion formulation, the optimal formulation was determined: microcrystalline cellulose: (chitosan∶Carbomer 940 = 2∶1), the adhesive material dosage accounted for 20% of the excipient dosage, and the ratio of drugs to excipients was 1 : 4. All animal experiments have been approved by Ethics Committee of Shanghai University of Traditional Chinese Medicine. The in vivo and in vitro adhesive evaluation results showed the pellets had a clear advantage in intestinal adhesion over normal pellets, its also proved the scientificity and reliability of the method of screening bioadhesive formulation.

Effect of different combinations of bracket, archwire and ligature on resistance to sliding and axial rotational control during the first stage of orthodontic treatment: An in-vitro study / 대한치과교정학회지

OBJECTIVE: This study was performed to explore the effect of different bracket, archwire, and ligature combinations on resistance to sliding (RS) and rotational control in first-order angulation. METHODS: Three types of brackets (multi-level low friction [MLF], self-ligating, and conventional brackets) coupled with four nickel-titanium archwires (0.012, 0.014, 0.016, and 0.018-inch diameter) and two stainless steel ligatures (0.20 and 0.25 mm) were tested in different first-order angulations (0°, 2°, 4°, 6°, 8°, 10°, 15°, 20°) by using an Instron universal mechanical machine in the dry state at room temperature. RS value was evaluated and compared by one-way ANOVA. RESULTS: Under the same angulation, the RS values showed the following order: conventional brackets > MLF brackets > self-ligating brackets. The RS was the highest for conventional brackets and showed a tendency to increase. The RS for MLF brackets coupled with thinner archwires and ligatures showed a similar tendency as the RS for the self-ligating bracket. In contrast, the RS for MLF brackets coupled with thicker archwires and ligatures increased like that for conventional brackets. MLF brackets showed the greatest range of critical contact angles in first-order angulation. CONCLUSIONS: The RS in first-order angulation is influenced by bracket design, archwire, and ligature dimension. In comparison with self-ligating and conventional brackets, MLF brackets could express low friction and rotational control with their greater range of critical contact angles.

Optimization of dry granulation prescription and technology of Anti-Hashimoto’s Thyroiditis Formula Granules based on physical characteristics of raw materials in preparations / 中草药

Objective To optimize the prescription of dry granulation process of Anti-Hashimoto’s Thyroiditis Formula Granules. Methods Regarding primary formation rate, friability, and dissolubility and comprehensive in granulation process as indexes, the physical properties of water content, the angle of repose and the degree of compression were investigated to select dry granulation prescription. The technological parameters including horizontal speeds, rotate speed of roller and pressure rollers were screened by L9(34) orthogonal experiment were composed to be optimal technological prescription, and the optimum process was verified. Results The optimum lubricant and accessories ratio were 0.5% magnesium stearate and 20% dextrin respectively. The optimized dry granulation process parameters: horizontal speed 30 r/min, press roll speed 5 r/min and press roll pressure 7 MPa. Conclusion The optimized dry granulation preparation technology is feasible and reasonable, which shows good flakes continuous and granules with color uniformity, suitable rigidity and well formability in dry granulation preparation. After three batches of pilot-scale test, the dry granulation preparation technology is stable and feasible.

Effect of Polymerization Cycles on Gloss, Roughness, Hardness and Impact Strength of Acrylic Resins

Abstract The aim of this study was to evaluate the conventional and boiled polymerization cycles on gloss, roughness, hardness and impact strength of acrylic resins. Samples were made for each Classico and QC-20 materials (n=10) in dental stone molds obtained from rectangular metallic matrices embedded in metallic flasks. The powder-liquid ratio and manipulation of the acrylic resins' were accomplished according to manufacturers' instructions and the resins were conventionally packed in metallic flasks. After polymerization by (1) conventional: 74 °C for 9 h (Classico) and (2) boiled: 20 min (QC-20) cycles, the samples were deflasked after cooling at room temperature and conventionally finished and polished. The properties were evaluated after storage in water at 37 °C for 24 h. Gloss was verified with Multi Gloss 268 meter (Konica Minolta), surface roughness was measured with Surfcorder SE 1700 rugosimeter (Kosaka), Knoop hardness number was obtained with HMV-200 microdurometer, and impact strength was measured in an Otto Wolpert-Werke device by Charpy system (40 kpcm). Data were subjected to Student's t-test (at α=0.05). The results were: Gloss: 67.7 and 62.2 for Classico and QC-20 resins, respectively; Surface roughness: 0.874 and 1.469 Ra-µm for Classico and QC-20, respectively; Knoop hardness: 27.4 and 26.9 for Classico and QC-20, respectively; and Impact strength: 37.6 and 33.6 kgf/cm2 for Classico and QC-20, respectively. No statistically significant difference (p>0.05)were found between the resins for the evaluated properties. In conclusion, conventional and boiled polymerization cycles had similar effects on gloss, roughness, hardness and impact strength of both Classico and QC-20 resins.

Resumo O propósito neste estudo foi avaliar os ciclos de polimerização convencional e por fervura sobre o brilho, rugosidade, dureza e resistência ao impacto de resinas acrílicas. Amostras foram confeccionadas para cada resina Clássico ou QC-20 (n=20) em moldes de gesso obtidos de matrizes metálicas retangulares incluídas em muflas metálicas. A proporção monômero/polímero das resinas e manipulação foram de acordo com as recomendações dos fabricantes e a massa convencionalmente incluída em muflas metálicas. Após polimerização nos ciclos (1) convencional: 74 °C por 9 horas (Clássico) e (2) fervura: 20 min (QC-20), as amostras foram demufladas após esfriadas em temperatura ambiente e convencionalmente acabadas e polidas. As propriedades foram avaliadas após armazenagem das amostras em água a 37 °C por 24 h. O brilho foi verificado com medidor Multi Gloss 268 (Konica Minolta), a rugosidade avaliada com rugosímetro Surfcorder SE 1700 (Kosaka), a dureza Knoop foi obtida com microdurômetro HMV-200 (Shimadzu) e a resistência ao impacto determinada pelo sistema Charpy (Otto Wolpert Werke). Os dados submetidos ao teste t de Student (α=0.05) mostraram que Os resultados foram: brilho: 67,7 e 62,2 para Clássico e QC-20, respectivamente; rugosidade: 0,874 e 1,469 Ra-µm para Clássico e QC-20, respectivamente; dureza: 27,4 e 26,9 para Clássico e QC-20, respectivamente; e resistência ao impacto: 37,6 e 33,6 kgf/cm2 para Clássico e QC-20, respectivamente. Não houve diference estatisticamente significante entre as resinas para as propriedades avaliadas. Conclui-se que os ciclos de polimerização convencional e por fervura promoveram similares efeitos sobre o brilho, rugosidade, dureza e resistência ao impacto para ambas as resinas Clássico e QC-20.

Exploration of action and significance of-source point for clinical diagnosis based on literature metrology / 中国针灸

Modern literature on the physical property of the-source point were collected from Chinese National Knowledge Infrastructure(CNKI) and China Biology Medicine(CBM) databases. The physical property,relevant diseases and-source acupoints were analyzed through statistical analysis of literature metrology. It is considered that articles on the electrical resistance of acupoint account for the largest part,which are mainly related to hyperthyreosis and the change of menstrual cycle. The second part is radiation spectrum,which are mostly relevant to the coronary heart disease and then the physiological change of healthy people. As to the diseases,articles of cardiovascular diseases are taken the most proportion,which were treated with the 12-source points,Shenmen(HT 7) and Daling(PC 7). Also,the results present the physical property of-source acupoints in themeridians is more sensitive to diseases and the physical property is specific to diseases. Besides,the-source acupoint can show the pathological changes of its own meridian.

Role of key physical parameters of andrographis paniculata (Burm. f.) Nees granules in their dissolution behavior / 中国药学杂志

OBJECTIVE: To establish the relationship between the physical parameters of granules and their dissolution behavior. METHODS: Andrographis paniculata (Burm. f.) Nees extract was utilized as a model drug. The extract was mixed with different excipients (MCC/soluble starch) at the ratio of 1:1 by weight using different methods. The granules were prepared by using high shear granulation and extrusion granulation methods. Then the dissolution behavior of the granules was evaluated by monitoring equilibrium dissolution quantity and dissolution rate constant. The effect of physical properties on the dissolution behavior was analyzed through stepwise regression. RESULTS: Particle size, critical relative humidity (CRH), moisture content, pore volume, and tapped density were the main factors related to the dissolution behavior of granules. CONCLUSION: A higher equilibrium dissolution quantity could be obtained with higher moisture content, smaller particle size, and lower CRH. There is a positive correlation between dissolution rate constant and tapped density of granules, and a negative correlation with particle size (D[4, 3]) and pore volume (PV).

Effect of physical properties of microcrystalline cellulose on its compressibility and compactability / 中国药学杂志

OBJECTIVE: To study correlation between physical properties and compressibility and compactablility of Microcrystalline cellulose. METHODS: After determining the physical properties such as particle size distribution, moisture capacity, angle of repose, bulk density, tapped density, the powder was tableted by the Korsch XP1 at the same filling height, and data derived from heckle model, plasticity constant, cumulative elastic recovery, tensile strength and it's changes with time were evaluated. RESULTS: The physical properties of microcrystalline cellulose had great effect on its compactablility as well as cumulative elastic recovery out of die, but not on compressibility. And pressure applied correlated closely with changes of tensile strength in storage, which was intensified by the influence of water in powder on the particle size. CONCLUSION: Microcrystalline cellulose shows excellent compressibility, however, particle size reduction is able to decrease the compactability. Since the water in powder can increase particle size by changing internal structure of particles and plays a prerequisite role in lubrication and adherence, the variation of water content may weaken the compatability of microcrystalline cellulose and worsen the mechanical strength stability of tablets in storage.

Hygroscopicity of Liuwei Dihuang powder and its correlation of physical properties / 中草药

Objective: To investigate the hygroscopic properties of Liuwei Dihuang extract, and the correlation between the tensile strength and physical properties such as moisture content, angle of repose, critical relative humidity (CRH), and Karnofsky index. Methods: Liuwei Dihuang extract was used as a model, added with various excipients in different ways, and their hygroscopic properties were examined. Using the method of multiple linear regression analysis, the correlation between tensile strength and the physical properties of Liuwei Dihuang raw materials was studied. Results: The hygroscopicity of Liuwei Dihuang extract with various excipients was improved, negatively correlated with angle repose, compression index, bulk density, and moisture acceleration, and positively correlated with water solubility, water content, CRH, equilibrium moisture content, and initial velocity of hygroscopicity. Conclusion: The physical properties of Liuwei Dihuang powder affects the tensile strength of its tablets formed directly.

Variations in surface roughness of seven orthodontic archwires: an SEM-profilometry study / 대한치과교정학회지

OBJECTIVE: The purpose of this study was to evaluate the surface roughness (SR) of 2 types of orthodontic archwires made by 4 different manufacturers. METHODS: This in vitro experimental study was conducted on 35 specimens of 7 different orthodontic archwires, namely, 1 nickel-titanium (NiTi) archwire each from the manufacturers American Orthodontics, OrthoTechnology, All-Star Orthodontics, and Smart Technology, and 1 stainless steel (SS) archwire each from the manufacturers American Orthodontics, OrthoTechnology, and All-Star Orthodontics. After analyzing the composition of each wire by energy-dispersive X-ray analysis, the SR of each wire was determined by scanning electron microscopy (SEM) and surface profilometry. Data were analyzed using the Kruskal-Wallis and Mann-Whitney U tests (alpha < 0.05). RESULTS: The average SR of NiTi wires manufactured by Smart Technology, American Orthodontics, OrthoTechnology, and All-Star Orthodontics were 1,289 +/- 915 Adegrees, 1,378 +/- 372 Adegrees, 2,444 +/- 369 Adegrees, and 5,242 +/- 2,832 Adegrees, respectively. The average SR of SS wires manufactured by All-Star Orthodontics, OrthoTechnology, and American Orthodontics were 710 +/- 210 Adegrees, 1,831 +/- 1,156 Adegrees, and 4,018 +/- 2,214 Adegrees, respectively. Similar to the results of profilometry, the SEM images showed more defects and cracks on the SS wire made by American Orthodontics and the NiTi wire made by All-Star Orthodontics than others. CONCLUSIONS: The NiTi wire manufactured by All-Star Orthodontics and the SS wire made by American Orthodontics were the roughest wires.

Mechanical evaluation of the resistance and elastance of post-burn scars after topical treatment with tretinoin

OBJECTIVE: After burn injuries, scarred skin lacks elasticity, especially in hypertrophic scars. Topical treatment with tretinoin can improve the appearance and quality of the skin (i.e., texture, distensibility, color, and hydration). The objective of this prospective study was to examine the effects of treatment with 0.05 percent tretinoin for one year on the biomechanical behavior and histological changes undergone by facial skin with post-burn scarring. Setting: Tertiary, Institutional. METHOD: Fifteen female patients who had suffered partial thickness burns with more than two years of evolution were selected. Skin biopsies were obtained initially and after one year of treatment. The resistance and elastance of these skin biopsies were measured using a mechanical oscillation analysis system. The density of collagen fibers, elastic fibers, and versican were determined using immunohistochemical analysis. RESULTS: Tretinoin treatment significantly lowered skin resistance and elastance, which is a result that indicates higher distensibility of the skin. However, tretinoin treatment did not significantly affect the density of collagen fibers, elastic fibers, or versican. CONCLUSION: Topical tretinoin treatment alters the mechanical behavior of post-burn scarred skin by improving its distensibility and thus leads to improved quality of life for patients.

Physical properties and surface topography of orthodontic stainless steel wires: comparing a new Korean product with others from foreign companies / 대한치과교정학회지

The purpose of this study was to investigate the property of a new Korean stainless steel wire(Jinsung Ind.) comparing with other foreign products. Five types of stainless steel wires (Standard, Resilient, HI-T of Unitek, Stainless steel of Ormco and Jinsung Ind.) in 0.016x0.022 and 0.019x0.025were tested to observe for composition analysis, size difference, tensile properties, flexure bending property, tortion property, surface hardness and surface topography by means of SEM. The findings suggest that: 1. In maximum tensile strength of tensile properties, Unitek Hi-T showed the greatest value, followed by Unitek Resilient, Jinsung Stainless Steel, Ormco Stainless Steel, Unitek Standard in 0.016x0.022, and Unitek Hi-T showed highest value, followed by Jinsung Stainless Steel, Ormco Stainless Steel, Unitek Resilient, Unitek Standard in 0.019x0.025. 2. In elongation rate, Unitek Standard showed the greatest value, followed by Ormco Stainless Steel, Unitek Hi-T, Unitek Resilient, Jinsung Stainless Steel in 0.016x0.022, and Unitek Hi-T showed the highest value, followed by Unitek Standard, Ormco Stainless Steel, Jinsung Stainless Steel, Unitek Resilient in 0.019x0.025. 3. In modulus of elasticity, Jinsung Stainless Steel showed the greatest value, followed by Unitek Hi-T, Unitek Resilient, Ormco Stainless Steel, Unitek Standard in 0.016x0.022, and Unitek Resilient showed the highest value followed by Jinsung Stainless Steel, Ormco Stainless Steel, Unitek Hi-T, Unitek Standard in 0.019x0.025. 4. In bending fatigue test, Jinsung Stainless Steel showed the greatest fracture resistance, followed by Unitek Hi-T, Unitek Standard, Unitek Resilient, Ormco Stainless Steel in 0.016x0.022, and Unitek Hi-T showed the greatest fracture resistance followed by Jinsung Stainless Steel, Unitek Resilient, Unitek Standard, Ormco Stainless Steel in 0.019x0.025. 5. In twist test, Unitek Resilient showed the greatest fracture resistance, followed by Jinsung Stainless Steel, Unitek Hi-T, Ormco Stainless Steel, Unitek Standard in 0.016x0.022, and Jinsung showed the greatest fracture resistance, followed by Unitek Resilient, Unitek Standard, Ormco Stainless Steel, Unitek Hi-T. 6. In surface topography, every products showed indentation and pitting. Jinsung stainless steel wire showed long thin indentation and relatively smooth surface. Unitek wires showed indentation and pitting and Ormco wire showed a lot of irregular pittings.